Avery Berkel 6720 Instrukcja Użytkownika

User’s ManualModel6700FamilyModel 6720Model 6702Model 6710Point-of-SaleInterface Scales

Model 6700 Family User’s Manual10There are three modes available to you withSwitch 1 in the Menu mode or OPEN position.They are as follows:DIAG (Diagn

Model 6700 Family User’s Manual11Figure 3Menu Structure

Model 6700 Family User’s Manual12AlternateCalibration PointsTable 1AlternativeCalibration PointsBaud Rate andParity OptionsTable 2Baud Rate andParity

Model 6700 Family User’s Manual13The Diagnostic (DIAG) mode menu allowstesting of specific areas of the scale’s functionand viewing current configura

Model 6700 Family User’s Manual14If you encounter anyfailure in these tests,contact your localWeigh-Tronix dealer.Press the ZERO key toscroll through

Model 6700 Family User’s Manual159. With a loopback connector in place, pressthe TEST key to perform the I/O test…PASS or FAIL is displayed briefly, t

Model 6700 Family User’s Manual1618. Press the ZERO key…FILT is displayed. This stands for filter-ing.19. Press the TEST key…The current filter settin

Model 6700 Family User’s Manual17The Configuration (CONF) Mode menu allowsscale configuration for your specific applicationneeds. The items you can co

Model 6700 Family User’s Manual182. Press the TEST key…FILT is displayed.3. Press the TEST key…The current setting, FAST or SLO,is displayed.4. Use th

Model 6700 Family User’s Manual19The Calibration (CAL) Mode menu lets youcalibrate your scale. The items in the calibrationmenu are as follows:POUNDS/

Model 6700 Family User’s Manual2Risk of electrical shock. Do not remove cover. No user serviceableparts inside. Refer servicing to qualified service p

Model 6700 Family User’s Manual205. When the desired capacity is displayed,press the TEST key. . .That choice is accepted and LOAD 0 isdisplayed.6. Cl

Model 6700 Family User’s Manual21The TEST key located on the front panel lets youperform some basic system diagnostics, as wellas review the current s

Model 6700 Family User’s Manual22CommunicationCommunicationsEnabledSerial DataTransmissionModem control lineswill not be supportedfor RS-2324-Bit Para

Model 6700 Family User’s Manual23The scale end of the interface cable plug is a DA15 pin socket. The other end is as required byyour application.Below

Model 6700 Family User’s Manual24Error CodesThe 9-pin version of the 6700 has DE typefemale connector accessible at the rear of theunit. The functiona

Model 6700 Family User’s Manual25Perform the following steps in the order pre-sented until the described problem is corrected.No Power (Display is Bla

Model 6700 Family User’s Manual26Display shows unrecognized characters1. Check software PROM for proper insertion.2. Check display cables for the prop

Model 6700 Family User’s Manual27Scale is not transmitting data to the hostdevice1. Check cable connection at both the rearof the scale and the host d

Model 6700 Family User’s Manual28Notes

Model 6700 Family User’s Manual29

Model 6700 Family User’s Manual3Specifications ... 4Initial Setup ...

Model 6700 Family User’s Manual30

Model 6700 Family User’s Manual31

1000 Armstrong DriveFairmont, MN 56031Telephone: 507-238-4461Facsimile: 507-238-4195E-Mail: [email protected]

Model 6700 Family User’s Manual4SpecificationsDescriptionCapacity/Resolution Agency Certificates of ConformanceThe NCI 6700 models are digital electr

Model 6700 Family User’s Manual5Model 6702: 10.4 x 6.4 x 2.5Model 6710: 10.4 x 10.4 x 2.5Model 6720: 14.1 x 12.6 x 4.1Model 4740: 14.0 x 10.0UL/CSA ap

Model 6700 Family User’s Manual6Under Capacity LimitsOver Capacity LimitsSealingInternal CountsDynamic ResponseCommunicationsUnder capacity indication

Model 6700 Family User’s Manual7Initial Setup1. Remove contents of the shipping container.2. Inspect the scale for evidence of shippingdamage. Immedia

Model 6700 Family User’s Manual8OperationPower Up TestSequenceIf RAM or ROM erroris reported, you mustpress the TEST key toacknowledge thecondition.

Model 6700 Family User’s Manual91. With the scale powered on, make sure thescale platter is empty and the display is atzero. If it is not, press the Z